Build A MustangSteve 400HP 351 Windsor

BLOCK, CRANK, PISTONS AND RODS

1969 351 WINDSOR BLOCK 4.030″ BORE
STOCK 1969 CRANK, .010/.010  3.500″ STROKE
1992 TRUCK RODS, RWORKED, STD
ARP #150-6004 ROD BOLTS
CLEVITE 77 MAIN BEARINGS
CLEVITE 77 ROD BEARINGS
TRW L-2446-F FORGED PISTONS +.030″
HASTINGS MOLY RINGS
MACHINE WORK  –  BALANCE ASSY, FLYCUT PISTONS

HEADS

EDELBROCK #6025 1.90/1.60 PERFORMER RPM ALUMINUM HEADS
ARP #154-3603 HEAD BOLTS
FEL PRO #1011-1 HEAD GASKETS QTY 2

CAMSHAFT

COMPETITION CAMS 1331-16 MAGNUM ROLLER ROCKER ARMS
CRANE #44306-1 RETROFIT ROLLER LIFTER KIT
CRANE #44630-16 RETROFIT PUSH RODS
CRANE #449631 RETROFIT ROLLER CAM 282/290 220/228/.542/.563 112LC
EDELBROCK DOUBLE ROLLER TIMING CHAIN #EDL-7820INDUCTION & FUEL


WEILAND STEALTH INTAKE MANIFOLD, PORT MATCHED
CARTER #M-6904 MECHANICAL FUEL PUMP
HOLLEY 700CFM DOUBLE PUMPER CARB
COBRA OVAL ALUMINUM AIR CLEANEREXHAUST

HEDDMAN #88660-6 HEADERS (LONG) jet coatedLUBRICATION

ARP #154-7901 OIL PUMP DRIVE SHAFT
COBRA ALUMINUM OIL PAN #A6675E
MELLING M83HV HIGH VOLUME OIL PUMP
IGNITION

MSD BILLET ELECTRONIC DISTRIBUTOR
MSD -6A IGNITION
MALLORY PROMASTER COIL
FORD MOTORSPORT DISTRIBUTOR GEAR #M-12390-F
TAYLOR BLACK IGNITION WIRES W/ 115 DEGREE BOOTS
COOLING

MILDON ALUMINUM WATER PUMP
STANT THERMOSTAT #0-33342-05410 (180)
MISCELLANEOUS

ARP STAINLESS STEEL 6 POINT ENGINE BOLT KIT
FEL PRO GASKET SET (LESS HEADS/REAR MAIN)
FORD D2AZ6379B FLYWHEEL NOLTS (FOR FLEXPLATES) QTY 6
FLEXPLATE  157 tooth
SUM-163594 BALANCER TIMING TAPEHOW MUCH DOES ALL THAT STUFF COST?
Plan on about $5,000 plus the labor to assemble and install.

Technical Information

FAQs

What bearings do I use for a 69 Mustang?

69 spindles have smaller axle on all except BOSS 302 and BOSS 429.  69 non-Boss spindles use A2 and A6 bearings. 70-73 spindles have larger diameter axle and use A12 and A13 bearings.

69 non-Boss spindles use smaller tie rod, same as 67-69 Mustang.

70 spindles use a larger tie rod that is a little larger than the 67-69 spindle, but smaller than the Granada spindle.

What hubs do I use on what spindles?

Hubs and rotors from 65-73 will fit either spindle as long as the bearings that fit the spindle axle are used. The OD of the bearings is the same for all years mentioned.

So, the 70-73 spindle has larger axle but the rollers in the bearings are actually smaller than the 65-69 bearing rollers.

Will your rear brakes work on the Torino (new style) bolt pattern?

Yes.  The big bearing cobra rear brackets will work with the Torino (new style) bolt pattern using 3/8” mounting bolts and will also fit the older style large bearing 9” flanges using ½” bolts.

The brake gap needs to be 2.50”.  That is measured from the outside of the housing flanges to the outside of the axle flange (where the rotor would fit, but not including the thickness of the rotor.

Brake Pedal FAQs